Items from RAM Audio


Ram Audio ADM 24 - 19" DSP Controller

  • Two Inputs and four Outputs: configurable as two way stereo and three or four way mono processor
  • 24 bits/96 kHz A/D and D/A converters
  • 32 bits floating point DSPs. 56 bits internal resolution
  • USB and EtherNet port conection to PC
  • 50 storing memories

Input Configuration

  • Gain control
  • Delay Line: 0 to 20 meters
  • EQ: 29 full configuration filters per input (Parametric, Shelving, LowPass, HiPass, BandPass, StopBand, AllPass)

Output Configuration

  • Free Routing
  • Output Delay: 0 to 7 meter
  • Crossovers: Up to 8th Order (48dB/Oct). Butterworth, Linkwitz-Riley and Bessel
  • Output EQ: 9 full configuration filters (Parametric, Shelving, LowPass, HiPass, BandPass, StopBand, AllPass)
  • Gain, Mute and Phase inversion
  • RMS and Peak Compressor/Limiter with adjustable knee, which permits a progressive limitation threshold offering a more transparent effect when compared with conventional limiters. Absolutely distortion free Dynamics Control.
  • Noise Gate
  • Possibility to use the acoustic system parameters, magnitude and phase, and refer to the system's Total Electro-acoustic response so that "you hear what you see"

Download ADM 24 Software

Technical Specifications

  • Type: Digital
  • Model: Stereo 2-way/mono 4-way
  • AD/DA converter: 24 bits
  • Sampling frequency: 48 kHz
  • Frequency response: 20 Hz - 20kHz
  • Filter type: IIR x-overs: Linkwitz-Riley, Butterworth, Bessel, EQ: Parametric, Shelving, LowPass, HighPass, BandPass, StopBand, AllPass
  • Filter slew rate: 6/12/18/24/30/36/42/48 dB/Oct
  • Dynamic range: > 110 dB
  • THD:
  • Crosstalk: > 90 dB
  • Max. input level: +20 dBu
  • Max. output level: +20 dBu
  • Input impedance: 12 kOhm
  • Output impedance: 50 Ohm
  • Controls: Push Encoder
  • Display: 24x2 Characters
  • Line inputs: 2
  • Line input connectors: Neutrik XLR
  • Line outputs: 4
  • Line output connectors: Neutrik XLR
  • Interfaces: USB, Ethernet
  • Mains connector: IEC-Schuko
  • Operating voltage: 85 - 265 V AC, 50-60 Hz
  • Width: 19"
  • Height: 1 U
  • Accessories (included): USB cable, Mains IEC-Schuko cable
Item no.: ADHRAMADM24

Ram Audio AES 322 - AES/EBU Digital Input Module for RAMDSP22W

Item no.: ADHRAMAES322W

Ram Audio DSP 22 S - DSP Module for S Series 2-Channel Professional Power Amplifiers

Fully programmable Digital Signal Processor with USB connectivity.

  • Product category: extension module
  • Type: digital signal processor
  • Channels: 2
  • AD/DA conversion: 24-bit
  • Sampling rate: 192 kHz (256x oversampling)
  • Filter types: Butterworth, Bessel, Linkwitz-Riley
  • Filter slope: up to 48 dB/octave
  • Output EQ: 9 filters (parametric, shelving, LP, HP, BP, SB) each channel
  • Output Delay: up to 7.1 m (20.69 ms) each channel
  • Limiter: RMS Power, Peak Voltage Output each channel
  • Additionakl DSP functions: Gain, Mute, Phase Inversion each channel
  • Line inputs: 2
  • Line input connectors: XLR balanced
  • Line outputs: 2
  • Line output connectors: XLR balanced
  • Programming: via USB port
Item no.: ADHRAMDSP22S

Ram Audio DSP 22 W - DSP Module for W Series 2-Channel Professional Power Amplifiers

The W Series 2-Channel Digital Signal Processor is fully programmable in real time via USB, an optional Ethernet network or the front panel. The module features user configurable signal routing and post-processing XLR outputs to feed the processed signal to amplifiers without DSP. More than 50 presets can be saved and stored inside the amp.

  • Product category: extension module
  • Type: digital signal processor
  • Channels: 2
  • AD/DA conversion: 24-bit
  • Sampling rate: 48 kHz
  • Filter types: Butterworth, Bessel, Linkwitz-Riley
  • Filter slope: up to 48 dB/octave
  • Input EQ: 29 x parametric or 29 x graphic each channel
  • Output EQ: 20 filters (parametric, shelving, LP, HP, BP, SB) each channel
  • Input delay: up to 80 m (230 ms) each channel
  • Output delay: up to 18 m (50 ms) each channel
  • Limiter: RMS Power, Peak Voltage Output each channel, variable knee
  • Additionakl DSP functions: Gain, Mute, Phase Inversion each input and output
  • Line inputs: 2
  • Line input connectors: XLR balanced
  • Line outputs: 2
  • Line output connectors: XLR balanced
  • Programming: via USB port or Ethernet (optional)
  • Additional features: signal generator (pink noise, white noise, sine wave 20 Hz - 20.000 Hz)
Item no.: ADHRAMDSP22W

Ram Audio DSP 22 WE - Ethernet Module for RAMDSP22W

The EtheRAM� II module provides control and monotoring of a group of installed power amplifiers. It is connected to a standard Ethernet network and compatible with Crestron® and AMX® control systems as well as Stardraw Control® software.

  • Product category: extension module
  • Type: Ethernet
  • Connector: RJ45
  • Compatibble with: Crestron®; AMX®, Stardraw Control®
Item no.: ADHRAMDSP22WE

Ram Audio MDi2-1K4 - PA Amplifier 2 x 700 W 4 ohms

Item no.: ADHRAMMDI21K4

Ram Audio MDi2-6K - PA Amplifier 2 x 3000 W 4 Ohms

Item no.: ADHRAMMDI26K

Ram Audio MDi4-12K - 4 Channels Amplifier 4 x 3000 W 4 Ohms

Item no.: ADHRAMMDI412K

Ram Audio MDi4-2K4 - 4 Channels Amplifier 4 x 610 W 4 Ohms

Item no.: ADHRAMMDI42K4

Ram Audio MDi4-6K - 4 Channels Amplifier 4 x 1500 W 4 Ohms

Item no.: ADHRAMMDI46K

Ram Audio MDi8-2K7 - 8 Channels Amplifier 8 x 340 W 4 Ohms

Item no.: ADHRAMMDI82K7

Ram Audio MDi8-6K - 8 Channels Amplifier 8 x 750 W 4 Ohms

Item no.: ADHRAMMDI86K

Ram Audio S 1500 - PA Power Amplifier 2 x 880 W 2 Ohms

Compact 2 and 4-channel Power Amplifiers with state-of-the-art QuantaPulse EVO SMPS

The state-of-the-art QuantaPulse EVO switched-mode power supply of the new S Series amplifiers provides major benefits: it increases efficiency and reliability, generates less heat and keeps the weight down. While delivering high output power S series amplifiers tip the scales at around 8 kg only.

S Series power amplifiers are available with 2 and 4 channels and output ratings from 1.5 to 6 kW. Housed in 30 cm deep, 2U rackmountable chassis the S series uses surface-mount technology with high component density for maximum reliability.

    Main Features
  • QuantaPulseâ?¢ EVO switched-mode power supply for maximum efficiency, increased output and reliability
  • five 2-channel models with up to 4 kW output power
  • very light weight (8 kg), 2U and 30 cm depth
  • electronic protection circuits
  • high component density surface-mount technology (SMT) provides mechanical strength and reliable operation
  • Neutrik XLR and Speakon connectors

QuantaPulseâ?¢ Technology: The Soft Switching Resonant QuantaPulse Power Supply is designed to provide plenty of power when needed monitoring the necessary parameters of voltage and current for a controlled performance at all times. Bi-directional data flow between the power supply and power amp module. Two very important characteristics of the QuantaPulse power supply are the optimization against over-voltages and superior reliability.

Technical Specifications:

  • Product type: Power amplifier
  • Type: 2-channel
  • Output power (1 kHz @ 2 ohms): 2 x 880 W
  • Output power (1 kHz @ 4 ohms): 2 x 575 W
  • Output power (1 kHz @ 8 ohms): 2 x 325 W
  • Output power (1 kHz @ 4 ohms, bridged mode): 1760 W
  • Output power (1 kHz @ 8 ohms, bridged mode): 1150 W
  • Circuit concept: Class H
  • Frequency response: 20 - 20,000 Hz
  • THD:
  • S/N ratio: 112 dB
  • Damping Factor: > 500
  • Crosstalk: > 75 dB
  • Voltage gain: 26 dB / 32 dB / 38 dB
  • Input sensitivity: 2.6 dB/ 1.3 dB/ 0.6dB
  • Input impedance: unbalanced 10 kohms, balanced 20 kohms
  • Protection: Soft start, power on/off transients, power on muting, overheating, DC voltage, high frequency, short circuit, open outputs, mismatching
  • Controls: Power, 2 x volume, dual/bridge switch
  • Indicators: Clipping, ready, signal, temperature, fault
  • Line input connectors: 2 x XLR
  • Line output connectors: 2 x XLR
  • Speaker output connections: 2 x Speakon
  • Cooling system: fan
  • Power supply: 230 V
  • Power consumption @ full load: 4.0 A
  • Width: 483 mm
  • Height: 89 mm
  • Depth: 310 mm
Item no.: ADHRAMS1500

Ram Audio S 2000 - PA Power Amplifier 2 x 1190 W 2 Ohms

Compact 2 and 4-channel Power Amplifiers with state-of-the-art QuantaPulse EVO SMPS

The state-of-the-art QuantaPulse EVO switched-mode power supply of the new S Series amplifiers provides major benefits: it increases efficiency and reliability, generates less heat and keeps the weight down. While delivering high output power S series amplifiers tip the scales at around 8 kg only.

S Series power amplifiers are available with 2 and 4 channels and output ratings from 1.5 to 6 kW. Housed in 30 cm deep, 2U rackmountable chassis the S series uses surface-mount technology with high component density for maximum reliability.

    Main Features
  • QuantaPulseâ?¢ EVO switched-mode power supply for maximum efficiency, increased output and reliability
  • five 2-channel models with up to 4 kW output power
  • very light weight (8 kg), 2U and 30 cm depth
  • electronic protection circuits
  • high component density surface-mount technology (SMT) provides mechanical strength and reliable operation
  • Neutrik XLR and Speakon connectors

QuantaPulseâ?¢ Technology: The Soft Switching Resonant QuantaPulse Power Supply is designed to provide plenty of power when needed monitoring the necessary parameters of voltage and current for a controlled performance at all times. Bi-directional data flow between the power supply and power amp module. Two very important characteristics of the QuantaPulse power supply are the optimization against over-voltages and superior reliability.

Technical Specifications:

  • Product type: Power amplifier
  • Type: 2-channel
  • Output power (1 kHz @ 2 ohms): 2 x 1190 W
  • Output power (1 kHz @ 4 ohms): 2 x 790 W
  • Output power (1 kHz @ 8 ohms): 2 x 460 W
  • Output power (1 kHz @ 4 ohms, bridged mode): 2380 W
  • Output power (1 kHz @ 8 ohms, bridged mode): 1580 W
  • Circuit concept: Class H
  • Frequency response: 20 - 20,000 Hz
  • THD:
  • S/N ratio: 113 dB
  • Damping Factor: > 500
  • Crosstalk: > 75 dB
  • Voltage gain: 26 dB/ 32 dB/ 38dB
  • Input sensitivity: 3.0 dB / 1.5 dB / 0.8 dB
  • Input impedance: unbalanced 10 kohms, balanced 20 kohms
  • Protection: Soft start, power on/off transients, power on muting, overheating, DC voltage, high frequency, short circuit, open outputs, mismatching
  • Controls: Power, 2 x volume, dual/bridge switch
  • Indicators: Clipping, ready, signal, temperature, fault
  • Line input connectors: 2 x XLR
  • Line output connectors: 2 x XLR
  • Speaker output connections: 2 x Speakon
  • Cooling system: fan
  • Power supply: 230 V
  • Power consumption @ full load: 4.8 A
  • Width: 483 mm
  • Height: 89 mm
  • Depth: 310 mm
Item no.: ADHRAMS2000

Ram Audio S 3000 - PA Power Amplifier 2 x 1570 W 2 Ohms

Compact 2 and 4-channel Power Amplifiers with state-of-the-art QuantaPulse EVO SMPS

The state-of-the-art QuantaPulse EVO switched-mode power supply of the new S Series amplifiers provides major benefits: it increases efficiency and reliability, generates less heat and keeps the weight down. While delivering high output power S series amplifiers tip the scales at around 8 kg only.

S Series power amplifiers are available with 2 and 4 channels and output ratings from 1.5 to 6 kW. Housed in 30 cm deep, 2U rackmountable chassis the S series uses surface-mount technology with high component density for maximum reliability.

    Main Features
  • QuantaPulseâ?¢ EVO switched-mode power supply for maximum efficiency, increased output and reliability
  • five 2-channel models with up to 4 kW output power
  • very light weight (8 kg), 2U and 30 cm depth
  • electronic protection circuits
  • high component density surface-mount technology (SMT) provides mechanical strength and reliable operation
  • Neutrik XLR and Speakon connectors

QuantaPulseâ?¢ Technology: The Soft Switching Resonant QuantaPulse Power Supply is designed to provide plenty of power when needed monitoring the necessary parameters of voltage and current for a controlled performance at all times. Bi-directional data flow between the power supply and power amp module. Two very important characteristics of the QuantaPulse power supply are the optimization against over-voltages and superior reliability.

Technical Specifications:

  • Product type: Power amplifier
  • Type: 2-channel
  • Output power (1 kHz @ 2 ohms): 2 x 1570 W
  • Output power (1 kHz @ 4 ohms): 2 x 1100 W
  • Output power (1 kHz @ 8 ohms): 2 x 630 W
  • Output power (1 kHz @ 4 ohms, bridged mode): 3140 W
  • Output power (1 kHz @ 8 ohms, bridged mode): 2200 W
  • Circuit concept: Class H
  • Frequency response: 20 - 20,000 Hz
  • THD:
  • S/N ratio: 115 dB
  • Damping Factor: > 500
  • Crosstalk: > 75 dB
  • Voltage gain: 26 dB / 32 dB / 38 dB
  • Input sensitivity: 3.6 dB / 1.8 dB / 0.9 dB
  • Input impedance: unbalanced 10 kohms, balanced 20 kohms
  • Protection: Soft start, power on/off transients, power on muting, overheating, DC voltage, high frequency, short circuit, open outputs, mismatching
  • Controls: Power, 2 x volume, dual/bridge switch
  • Indicators: Clipping, ready, signal, temperature, fault
  • Line input connectors: 2 x XLR
  • Line output connectors: 2 x XLR
  • Speaker output connections: 2 x Speakon
  • Cooling system: fan
  • Power supply: 230 V
  • Power consumption @ full load: 6.2 A
  • Width: 483 mm
  • Height: 89 mm
  • Depth: 310 mm
Item no.: ADHRAMS3000
Contact person