Telefon: +49 34671 550240 | eMail: info@licht-produktiv.de
Dynacord PM 502 Power Mixer

Item number: F01U297641

Category: Powermixer


1.069,00 €

including 19% VAT., no shipping costs (Paketversand)

Not available now!

Shipping time: 4 - 6 workdays



Description

Channels (mono + stereo): -5 + 3
Microphone inputs: -5 x XLR/Jack socket
Auxiliaries (FX, AUX): -1 Post, 1 Pre

Rated output power, 20-20000 Hz, THD < 0.5%, one channel loaded
- into 4 O: 640 W
- into 8 O: 350 W

Max. dual channel output power, dynamic headroom, IHF-A  
into 4 O: 2 x 600 W
into 8 O: 2 x 340 W

Max. single channel output power, continuous, 1 kHz, THD = 1% 
into 4 O: 500 W
into 8 O: 280 W

Max. midband output power, 1 kHz, THD = 1%, dual channel 
into 4 O: 2 x 450 W
into 8 O: 2 x 270 W

Rated output power, 20-20000 Hz, THD < 0.5%, one channel loaded 
into 4 O: 2 x 400 W
into 8 O: 2 x 240 W

Max. output power, Direct Drive mode (bridge configuration), continuous, 1 kHz, THD = 1%
into 12 O: 680 W
Maximum output voltage, power amplifier, 1 kHz, no load 
Dual channel mode: -52 Vrms
Direct Drive mode: -100 Vrms
THD, at 1 kHz, MBW = 22 kHz
MIC input to master A L/R outputs, +10 dBu, typical: < 0.015%
MIC iput to speaker output: < 0.15%
DIM 30, MIC input to speaker output, 3.15 kHz, 15 kHz: < 0.05%
IMD-SMPTE, MIC input to speaker outputs, 60 Hz, 7 kHz: < 0.15%
Frequency response, -3 dB, ref. 1 kHz
Any input to any Mixer output: 15?22000 Hz
Any input to Speaker output: 20?22000 Hz
Microphone mute switch attenuation
Amplifier Ch1/Ch2: < -85 dB
Channel to channel: < -78 dB
Microphone mute switch attenuation: > 100 dB
Channel VOL and FX/AUX send attenuation: > 85 dB
CMRR, MIC input, 1 kHz: > 80 dB
Input sensitivity, all level controls in max. position
MIC: 65 dBu (435 µV)
LINE (mono): -45 dBu (4.35 mV)
LINE (stereo): -27 dBu (34.6 mV)
CD (stereo): -27 dBu (34.6 mV)
All other outputs (impedance balanced)
MIC inputs, GAIN at min. position: +11 dBu
Mono line inputs, GAIN at min. position30 dBu
Stereo line inputs: +26 dBu
PHONES output: +21 dBu
MASTER A, B, AUX outputs: +11 dBu
Input impedances
MIC: 2 kO
CD: 10 kO
All other inputs: > 15 kO
Output impedances
PHONES: 47 O
All other outputs (impedance balanced): 150 O
MASTER VOLUME down: -129 dBu
Noise, channel inputs to MASTER A L/R outputs, MBW = 22 kHz, Aweighted
MASTER VOLUME down: -99 dBu
MASTER VOLUME center, all channel volume down: -90 dBu
MASTER VOLUME center, all channel volume center: -85 dBu
Signal-to-noise ratio, power amplifier, A-weighted, 450 W, 4 O: 104 dB
Output stage topology, amplifier: Class D
Equalization-
Low shelving filter: ±15 dB / 60 Hz
Mid peak filter: ±12 dB / 2.4 kHz
High shelving filter: ±15 dB / 12 kHz
Master EQ 7-band (63, 160, 400, 1k, 2.5k, 6k, 12k Hz): ±10 dB / Q = 1.5
Filter
Low-cut filter, microphone processing (switchable): 80 Hz, 18 dB/oct. or 150 Hz, 12 dB/oct.
Low-cut filter, amplifier (engaged in Direct Drive mode): 50 Hz or 70 Hz, 18 dB/oct.
Speaker processing: -LPN, switchable 
Delay MASTER B, selectable: 0?145 ms (0?50 m)

Effects
Type: Stereo 24/48-bit multi effects processor
Effect presets: 32 factory presets, user editable
Remote control: Footswitch
Display: 128 x 64 pixels, LCD
Audio player (USB at front panel)
Switching mode power supply (µC controlled): -FAT 32
Supported audio file formats: -MP3, WAV
Interface: -USB2.0, female type A
USB power supply, max. rated current (short circuit proof): -5 V, 500 mA
Digital audio interface (USB at rear panel)


Channels: -2 in, 2 out
AD/DA conversion: -16-bit, delta-sigma
Sampling rate: -32/44.1/48 kHz
PC interface: -USB2.0, female type B

Protection

MASTER A, B, AUX outputs: -Adjustable peak limiters, -10 ? +11 dBu
Amplifier: -Audio limiters, high temperature, DC, HF, short circuit, peak current limiters, turn-on delay, back EMF
Switching mode power supply (µC controlled): -Inrush current limiters, mains over/undervoltage, mains over current, high temperature
Cooling: -Continuous speed controlled fan
Phantom power, switchable: -48 V DC
AC power input: -100?240 V AC, 50?60 Hz
Power consumption, at 1/8 maximum output power, 4 O: -180 W
Safety class: I
Operating temperature: -5° to 40° C (40° to 105° F)
Product dimensions (Width x Height x Depth): -395 x 244 x 241 mm Rack-mount: 483 x 223 x 310.3 mm (7 HU)
Net weight: -4.9 kg
Shipping weight: -6.4 kg


This innovative product comes in a very modern and user-friendly design. It combines finest analogue input circuitry and operating surface with the advantages of its digital master and amplifier section making for a new dimension of flexibility in its class. The acoustical performance meets everything that you have come to expect from a quality Dynacord product.

Its feature package includes: 5 MIC/LINE input channels with compressor / limiter and talk-over function, 3 Stereo Inputs including Jack, RCA and USB connectors, onboard player for MP3 or WAV audio files, high quality effects section with 32 editable presets, 3 Master outputs with 7-band EQ each and flexible signal routing options, delay line for Master-B (150 msec / 50m), headphones control, LPN speaker processing, class-D  2 x 450W RMS respectively 2 x 600W / 4 Ohms IHF-A power, micro-controlled power supply (100V ? 240V), Direct-Drive option for 100V speaker lines, comprehensive protection package, live and install connectivity, optional rack mount kit.

The input structure of the PM 502, along with the entire feature package and connectivity, positions this mixer at the heart of many installations ranging from Bistros, small clubs, lounges, boutiques, hotel bars and lobbies to churches, mosques and a wide range of similar applications. Further the PM 502 is an extremely versatile tool for a multitude of live applications. It will be the ideal choice for entertainers, DJs and small bands looking for a compact and light-weight solution for live applications or rehearsal venues. The onboard MP3-Player on the front, allows the user to easily play pre-recorded music from a USB stick or a hard drive. The digital USB interface on the rear also allows for basic recording.

Ratings (0)

Average product review

Write your first review and help others with their purchase decision:

Product Tags

Please login first to add a tag.